PUMPING & FLUID HANDLING
Engineered Progressive Cavity Pumping (PCP) solutions for demanding industrial, oil & gas, and fluid-handling applications.
Our PCPs deliver stable, low-pulsation flow and are particularly suited to fluids that are difficult to handle with conventional pumping technologies.
Each PCP can be adapted to a wide range of operating conditions, including highly viscous, abrasive, solids-containing, and multiphase fluids.
Our PCPs deliver stable, low-pulsation flow and are particularly suited to fluids that are difficult to handle with conventional pumping technologies.
Each PCP can be adapted to a wide range of operating conditions, including highly viscous, abrasive, solids-containing, and multiphase fluids.
UP TO 340 m³/h
For high-volume fluid transfer
UP TO 72 BAR
For demanding pressure conditions
UP TO 3,000,000 mPa·s
For extremely viscous fluids
UP TO 50%
For solids-containing fluids
UP TO 8 m
For up to 8 m suction lift
UP TO 130°C
For elevated-temperature applications
PRODUCT RANGE
Our portfolio includes industrial, multiphase and downhole progressive cavity pumps designed for viscous, abrasive, gas-containing and solids-laden fluids, with configurations adapted to specific operating conditions.
INDUSTRIAL PCP
INDUSTRIAL PCP SERIES GENERAL CHARACTERISTICS:
- Flow rate: 10 l/h–340 m³/h
- Differential pressure: up to 72 bar
- Self-priming suction lift: up to 8 m
- Dynamic viscosity: up to 3,000,000 mPa·s
- Solids content: up to 50%
- Drive options: electric or hydraulic
- Rotor materials: carbon steel, stainless steel or tool steel
- Stator options: NBR, HNBR, EPDM, FKM or PTFE
- Temperature limit depends on the selected stator material
- Typical fluids: crude oil, fuel oil, sludge, emulsions, drilling mud, produced water and process chemicals
GIC60-24
COMPACT INDUSTRIAL PCP
For dosing, transfer and general industrial duties where installation space and cost are important.
For dosing, transfer and general industrial duties where installation space and cost are important.
- Capacity up to 60 m³/h
- Differential pressure up to 24 bar
- Electric drive
- Mechanical seal or application-specific sealing
- Baseplate or close-coupled configuration
GIS180-48
STANDARD INDUSTRIAL PCP
For continuous transfer of viscous, abrasive and solids-containing fluids.
For continuous transfer of viscous, abrasive and solids-containing fluids.
- Capacity up to 180 m³/h
- Differential pressure up to 48 bar
- Electric or hydraulic drive
- Bearing housing or block configuration
- Multiple rotor, stator, joint and seal options
GIH340-72
HEAVY-DUTY INDUSTRIAL PCP
For large flows, high pressure and demanding continuous operation.
For large flows, high pressure and demanding continuous operation.
- Capacity up to 340 m³/h
- Differential pressure up to 72 bar
- Electric or hydraulic drive
- Heavy-duty bearing arrangement
- Project-specific baseplate, coupling and drive package
VERTICAL PCP
VERTICAL PCP SERIES GENERAL CHARACTERISTICS:
- Flow rate: 0.5–340 m³/h
- Differential pressure: up to 18 bar
- Dynamic viscosity: up to 3,000,000 mPa·s
- Solids content: up to 50%
- Installation: vertical or semi-submersible
- Immersion length: project-specific
- Drive: electric
- Rotor and stator materials selected for the pumped fluid
- Temperature limit depends on the selected stator material
- Typical fluids: sludge, heavy oil, oily water, tank residues, process chemicals, abrasive suspensions and high-viscosity fluids
- Flow rate: 0.5–340 m³/h
- Differential pressure: up to 18 bar
- Dynamic viscosity: up to 3,000,000 mPa·s
- Solids content: up to 50%
- Installation: vertical or semi-submersible
- Immersion length: project-specific
- Drive: electric
- Rotor and stator materials selected for the pumped fluid
- Temperature limit depends on the selected stator material
- Typical fluids: sludge, heavy oil, oily water, tank residues, process chemicals, abrasive suspensions and high-viscosity fluids
GVS180-18
STANDARD VERTICAL PCP
For tanks, pits, vessels and process installations with limited floor space.
For tanks, pits, vessels and process installations with limited floor space.
- Capacity up to 180 m³/h
- Differential pressure up to 18 bar
- Vertical installation
- Electric drive
- Installation length engineered for the vessel
GVH340-18
HIGHCAP SEMI-SUBMERSIBLE PCP
For open tanks and sumps requiring the pumping element to be positioned inside the fluid.
For open tanks and sumps requiring the pumping element to be positioned inside the fluid.
- Capacity up to 340 m³/h
- Differential pressure up to 18 bar
- Semi-submersible construction
- Electric drive
- Customized immersion length
MULTIPHASE PCP
MULTIPHASE PCP SERIES GENERAL CHARACTERISTICS:
- Flow rate: up to 300 m³/h
- Differential pressure: up to 48 bar
- Temperature: up to 130°C
- Dynamic viscosity: up to 1,000,000 cP
- Fluid density: 800–1,400 kg/m³
- Free gas at pump inlet: up to 40%
- Operating pH range: 3–10
- Chlorides: up to 40 g/l
- CO₂: up to 5 g/l
- H₂S: up to 6 g/l
- Solids content: up to 45% at 5 Mohs, 20% at 6 Mohs or 10% at 7 Mohs
- Typical fluids: unseparated oil–gas–water mixtures, high-viscosity multiphase fluids, emulsions and gas-containing production fluids
- Flow rate: up to 300 m³/h
- Differential pressure: up to 48 bar
- Temperature: up to 130°C
- Dynamic viscosity: up to 1,000,000 cP
- Fluid density: 800–1,400 kg/m³
- Free gas at pump inlet: up to 40%
- Operating pH range: 3–10
- Chlorides: up to 40 g/l
- CO₂: up to 5 g/l
- H₂S: up to 6 g/l
- Solids content: up to 45% at 5 Mohs, 20% at 6 Mohs or 10% at 7 Mohs
- Typical fluids: unseparated oil–gas–water mixtures, high-viscosity multiphase fluids, emulsions and gas-containing production fluids
GMC120-24
COMPACT MULTIPHASE PCP
For individual wells, pilot projects and moderate gathering duties.
For individual wells, pilot projects and moderate gathering duties.
- Capacity up to 120 m³/h
- Differential pressure up to 24 bar
- Compact skid-mounted package
- Electric drive
- Suitable for oil-gas-water mixtures
GMS180-36
STANDARD MULTIPHASE PCP
General-purpose multiphase system for well-pad and field gathering applications.
General-purpose multiphase system for well-pad and field gathering applications.
- Capacity up to 180 m³/h
- Differential pressure up to 36 bar
- Electric or hydraulic drive
- Baseplate or skid-mounted package
- Instrumentation and control options
GMH300-48
HIGHCAP MULTIPHASE PCP
Heavy-duty multiphase pump for centralized gathering and long-distance transportation.
Heavy-duty multiphase pump for centralized gathering and long-distance transportation.
- Capacity up to 300 m³/h
- Differential pressure up to 48 bar
- Heavy-duty drive package
- Project-specific instrumentation
- Optional control and protection system
DOWNHOLE SURFACE-DRIVEN PCP
DOWNHOLE SURFACE-DRIVEN PCP SERIES GENERAL CHARACTERISTICS:
- Production rate: up to 200 m³/day
- Developed head: up to 2,400 m
- Installation depth: project-specific
- Drive: surface drive through a rotating rod string
- Production rate controlled by operating speed
- Oil density: 850–1,400 kg/m³
- Dynamic viscosity: up to 500,000 mPa·s
- Water cut: up to 99%
- Solids concentration: up to 5,000 mg/l
- Particle hardness: up to 7 Mohs
- Chlorides: up to 200 g/l
- Produced-water pH: 6.0–8.5
- Typical fluids: crude oil, heavy oil, oil–water emulsions and solids-containing production fluids
- Production rate: up to 200 m³/day
- Developed head: up to 2,400 m
- Installation depth: project-specific
- Drive: surface drive through a rotating rod string
- Production rate controlled by operating speed
- Oil density: 850–1,400 kg/m³
- Dynamic viscosity: up to 500,000 mPa·s
- Water cut: up to 99%
- Solids concentration: up to 5,000 mg/l
- Particle hardness: up to 7 Mohs
- Chlorides: up to 200 g/l
- Produced-water pH: 6.0–8.5
- Typical fluids: crude oil, heavy oil, oil–water emulsions and solids-containing production fluids
GDS40-1200
COMPACT SURFACE-DRIVEN PCP
For low-rate wells and compact artificial lift installations.
For low-rate wells and compact artificial lift installations.
- Capacity: up to 40 m³/day
- Head: up to 1,200 m
- Drive: surface drive with rod string
- Installation depth: project-specific
- Operating speed: selected for the required production rate
GDS100-1800
STANDARD SURFACE-DRIVEN PCP
For medium-rate production wells and demanding operating conditions.
For medium-rate production wells and demanding operating conditions.
- Capacity: up to 100 m³/day
- Head: up to 1,800 m
- Drive: surface drive with rod string
- Installation depth: project-specific
- Operating speed: selected for the required production rate
GDS200-2400
HIGHCAP SURFACE-DRIVEN PCP
For higher-rate artificial lift applications requiring increased production capacity and head.
For higher-rate artificial lift applications requiring increased production capacity and head.
- Capacity: up to 200 m³/day
- Head: up to 2,400 m
- Drive: surface drive with rod string
- Installation depth: project-specific
- Operating speed: selected for the required production rate
DOWNHOLE ELECTRIC SUBMERSIBLE PCP
DOWNHOLE ELECTRIC SUBMERSIBLE PCP SERIES GENERAL CHARACTERISTICS:
- Production rate: up to 200 m³/day
- Developed head: up to 2,400 m
- Installation depth: project-specific
- Drive: downhole electric motor
- Power supply: downhole power cable
- Rodless pumping system
- Suitable for directional and application-specific well completions
- Oil density: 850–1,400 kg/m³
- Dynamic viscosity: up to 500,000 mPa·s
- Water cut: up to 99%
- Solids concentration: up to 5,000 mg/l
- Particle hardness: up to 7 Mohs
- Typical fluids: crude oil, heavy oil, oil–water emulsions and solids-containing production fluids
GDE40-1200
COMPACT SUBMERSIBLE PCP
For low-rate wells requiring a compact rodless downhole pumping system.
For low-rate wells requiring a compact rodless downhole pumping system.
- Capacity: up to 40 m³/day
- Head: up to 1,200 m
- Drive: downhole electric motor
- Power supply: through downhole cable
- Installation depth: project-specific
GDE100-1800
STANDARD SUBMERSIBLE PCP
For medium-rate production and directional wells.
For medium-rate production and directional wells.
- Capacity: up to 100 m³/day
- Head: up to 1,800 m
- Drive: downhole electric motor
- Power supply: through downhole cable
- Installation depth: project-specific
GDE200-2400
HIGHCAP SUBMERSIBLE PCP
For higher-rate wells requiring a rodless system with increased production capacity and head.
For higher-rate wells requiring a rodless system with increased production capacity and head.
- Capacity: up to 200 m³/day
- Head: up to 2,400 m
- Drive: downhole electric motor
- Power supply: through downhole cable
- Installation depth: project-specific
MATERIALS & CONFIGURATIONS
Pump components can be selected and configured according to the pumped medium, operating temperature, pressure, abrasiveness, chemical composition and required service life.
ROTOR MATERIALS & COATINGS
Different rotor materials and surface treatments are available for applications involving abrasive, corrosive and demanding process media.
Material selection is based on the operating environment and required wear and corrosion resistance.
Material selection is based on the operating environment and required wear and corrosion resistance.
STATORS & ELASTOMERS
Stator materials are selected according to fluid composition, temperature, chemical compatibility and operating conditions.
Different elastomer formulations allow the pumping system to be adapted to hydrocarbons, chemicals, abrasive media and other challenging fluids.
Different elastomer formulations allow the pumping system to be adapted to hydrocarbons, chemicals, abrasive media and other challenging fluids.
ROTOR / STATOR GEOMETRIES
Different rotor and stator geometries can be selected to optimize flow capacity, differential pressure, efficiency and service life for the required application.
ENGINEERED AROUND YOUR OPERATING CONDITIONS
Every pumping application is different. Equipment selection and configuration are based on the actual characteristics of the process and pumped medium. This lets you configure the pumping system around the application rather than forcing the process around a standard pump.
- FLUID PROPERTIES
- Fluid composition and viscosity
- Gas content
- Solids concentration and particle size
- OPERATING CONDITIONS
- Required flow rate and differential pressure
- Operating temperature
- Abrasiveness
- MATERIAL COMPATIBILITY
- Chemical composition and corrosiveness
- Materials and elastomer compatibility
- Maintenance requirements
- SYSTEM CONFIGURATION
- Installation geometry and available space
- Drive configuration
- Existing equipment and connection dimensions
SPARE PARTS & LIFECYCLE SUPPORT
Our supply scope includes complete pumping units as well as wear parts and replacement components required throughout the equipment lifecycle.
- PUMPING & SEALING COMPONENTS
- Rotors
- Stators
- Mechanical seals
- Rings and gaskets
- WEAR & CONNECTION COMPONENTS
- Pins and sleeves
- Guide bushings
- Joint repair components
- Other pump-specific spare parts
- DRIVE & TRANSMISSION
- Drive shafts
- Connecting rods
- Articulated couplings
- TECHNICAL SUPPORT
- Pump selection and sizing
- Materials recommendations
- Replacement selection
- Installation guidance
- Ongoing spare-parts supply
REPLACEMENT & ALTERNATIVE SOLUTIONS
Existing pumping installations do not always require replacement with equipment from the original manufacturer.
We can evaluate the existing pump, operating conditions and process requirements and provide a technically compatible alternative — including complete pumping units, replacement components and wear parts.
- 1. EXISTING EQUIPMENT REVIEWReview of the installed pump, operating parameters, pumped medium, dimensions and connection requirements.
- 2. TECHNICAL MATCHINGSelection of a suitable pump configuration to meet the required flow, differential pressure, fluid characteristics and operating conditions.
- 3. MATERIALS & COMPONENTSSelection of rotor and stator materials, elastomers, seals and other components according to the application and pumped medium.
- 4. DROP-IN & ADAPTED SOLUTIONSWhere technically feasible, equipment can be configured around existing installation dimensions and connections, reducing the need for extensive system modifications.
- 5. LIFECYCLE SUPPORTOngoing supply of wear parts and replacement components, with technical support throughout the equipment lifecycle.
- AS A RESULT: A PROVEN, PRACTICAL ALTERNATIVE TO HIGH-COST OEM SOLUTIONS
APPLICATIONS
Progressive cavity pumps are used across industries where conventional pumping technologies face limitations due to viscosity, solids content, abrasiveness, multiphase flow or demanding operating conditions.
OIL & GAS
Progressive cavity pumps provide stable, low-pulsation transfer of viscous, solids-containing and multiphase production fluids across upstream and processing applications.
Typical pumped media: crude oil, heavy oil, produced water, oil-water emulsions, oily sludge, drilling mud and multiphase mixtures.
Suitable pump families: complete PCP range
Typical pumped media: crude oil, heavy oil, produced water, oil-water emulsions, oily sludge, drilling mud and multiphase mixtures.
Suitable pump families: complete PCP range
MINING & MINERAL PROCESSING
Designed for abrasive and solids-laden media where controlled flow and low product shear are required throughout mineral processing and dewatering operations.
Typical pumped media: mineral slurries, tailings, thickener underflow, flotation concentrates, mine water and reagent mixtures.
Suitable pump families:
Typical pumped media: mineral slurries, tailings, thickener underflow, flotation concentrates, mine water and reagent mixtures.
Suitable pump families:
- Industrial PCP
- Vertical PCP
CHEMICAL & PETROCHEMICAL
Accurate, low-pulsation pumping for viscous, shear-sensitive and chemically aggressive process media. We select wetted materials and elastomers for each application.
Typical pumped media: resins, polymers, adhesives, detergents, process chemicals, emulsions, paints and chemical sludge.
Suitable pump families:
Typical pumped media: resins, polymers, adhesives, detergents, process chemicals, emulsions, paints and chemical sludge.
Suitable pump families:
- Industrial PCP
- Vertical PCP
WASTEWATER & ENVIRONMENTAL
Progressive cavity pumps are widely used for controlled transfer, dosing and handling of media with changing viscosity and solids content.
Typical pumped media: primary and secondary sludge, dewatered sludge, screenings, polymers, lime slurry and wastewater containing suspended solids.
Suitable pump families:
Typical pumped media: primary and secondary sludge, dewatered sludge, screenings, polymers, lime slurry and wastewater containing suspended solids.
Suitable pump families:
- Industrial PCP
- Vertical PCP
CEMENT & CONSTRUCTION MATERIALS
Reliable transfer and metering of dense, abrasive mixtures used in cement production and construction-material processing.
Typical pumped media: cement slurry, gypsum slurry, mineral suspensions, coatings, additives, grout and wastewater containing fine solids.
Suitable pump families:
Typical pumped media: cement slurry, gypsum slurry, mineral suspensions, coatings, additives, grout and wastewater containing fine solids.
Suitable pump families:
- Industrial PCP
- Vertical PCP
FOOD & HYGIENIC PROCESSING
Gentle, low-pulsation transfer of viscous and shear-sensitive products. Hygienic configuration, wetted materials and cleaning requirements are defined for each process.
Typical pumped media: sauces, creams, syrups, concentrates, dairy products, fruit preparations, dough and food-processing by-products.
Suitable pump families: Industrial PCP — hygienic configuration
Typical pumped media: sauces, creams, syrups, concentrates, dairy products, fruit preparations, dough and food-processing by-products.
Suitable pump families: Industrial PCP — hygienic configuration
PROVEN IN REAL-WORLD OPERATION
Our pumping systems and components are developed with an experienced engineering and manufacturing team and are used in demanding industrial and oil & gas applications.
20+ YEARS OF EXPERIENCE
Application and engineering experience with progressive cavity pumping technologies.
100+ PUMP PROJECTS
Pumping solutions supplied for industrial and oil & gas applications.
REPLACEMENT EXPERIENCE
Pumps and components supplied as technically and commercially efficient alternatives to higher-cost established solutions.
DISCUSS YOUR PUMPING REQUIREMENTS
Looking for a pumping solution for viscous, abrasive, multiphase or solids-containing fluids?
We can review your operating requirements and help select a suitable equipment configuration for your application.
We can review your operating requirements and help select a suitable equipment configuration for your application.
- 1. DUTY REQUIREMENTS
- Required flow rate
- Required differential pressure
- Operating temperature
- 2. PUMPED MEDIUM
- Fluid composition and viscosity
- Solids content and particle size
- Gas content
- 3. INSTALLATION & EXISTING EQUIPMENT
- Installation conditions and available space
- Connection requirements
- Existing pump model and specifications, if applicable
- SEND US YOUR APPLICATION DATASend us your application and operating data at info@bontiss.com.
Unit 2904-05, 29/F, Universal Trade Center, No.3 Arbuthnot Road, Central, Hong Kong
Company Registration No.: 78298786
Email: info@bontiss.com
© 2026 BONTISS LIMITED. All rights reserved.
Company Registration No.: 78298786
Email: info@bontiss.com
© 2026 BONTISS LIMITED. All rights reserved.